Fabrication tools for a small shop.
Posted: Fri Apr 11, 2014 12:29 am
Greetings all!
Since I mainly focus on kitchen and bath remodels, I don't have much use for my fabrication tools anymore. Here is what I'm interested in selling. Everything is still in reasonable condition and should provide someone with good backup tools or for a small startup shop. I don't have prices figured out yet so hopefully we can come to reasonable offers. I hope to sell everything as a package deal rather than piece it all out. Please email me or call/text.
1. Blue Ripper Jr with Makita saw and a couple of used blades.
2. Seam polishing fixture. This is a custom fixture I designed before Omega Diamond came out with their version. It holds a Makita polisher and rides on the blue ripper rails.
3. BR Jr 7-foot and 13-foot rails
4. Amigo M2 router
5. Abaco 50 clamp
6. Fabrication table. Another contraption I came up with. Its approximately 8'x10' feet with a manually operated hydraulic tilt. In the upright position, it can be locked in place to transport a full slab. Its made out of 1/4 inch steel tubing and angle. Its bolted together for take down and setup. The table top is easily replaceable. I used 3/4 plywood waterproofed with a liquid tile membrane. The wear surface is high density foam. Patent pending.
7. Makita PW5001C motor only.
8. Brand new set of 7 polishing pads. I think I bought these from Tynan several years ago and just found them when I was cleaning shop.
9. Collection of router bits: 3/8 roundover position 1, Ogee position 1, 3cm bullnose position 1, position 3 and 3 polishing bits, 4cm bullnose position 1, straight bit with top bearing position 1 and position 2, T40 position 1, FB30 position 1, 3cm Demi position 1, and 3cm Bevel position 2
10. Maybe a few other hand tools or supplies.
Since I mainly focus on kitchen and bath remodels, I don't have much use for my fabrication tools anymore. Here is what I'm interested in selling. Everything is still in reasonable condition and should provide someone with good backup tools or for a small startup shop. I don't have prices figured out yet so hopefully we can come to reasonable offers. I hope to sell everything as a package deal rather than piece it all out. Please email me or call/text.
1. Blue Ripper Jr with Makita saw and a couple of used blades.
2. Seam polishing fixture. This is a custom fixture I designed before Omega Diamond came out with their version. It holds a Makita polisher and rides on the blue ripper rails.
3. BR Jr 7-foot and 13-foot rails
4. Amigo M2 router
5. Abaco 50 clamp
6. Fabrication table. Another contraption I came up with. Its approximately 8'x10' feet with a manually operated hydraulic tilt. In the upright position, it can be locked in place to transport a full slab. Its made out of 1/4 inch steel tubing and angle. Its bolted together for take down and setup. The table top is easily replaceable. I used 3/4 plywood waterproofed with a liquid tile membrane. The wear surface is high density foam. Patent pending.
7. Makita PW5001C motor only.
8. Brand new set of 7 polishing pads. I think I bought these from Tynan several years ago and just found them when I was cleaning shop.
9. Collection of router bits: 3/8 roundover position 1, Ogee position 1, 3cm bullnose position 1, position 3 and 3 polishing bits, 4cm bullnose position 1, straight bit with top bearing position 1 and position 2, T40 position 1, FB30 position 1, 3cm Demi position 1, and 3cm Bevel position 2
10. Maybe a few other hand tools or supplies.