Cry for HELP!! Kitchen faucet hole in wrong place??

Steve A · Post by **Steve A** » Wed Jun 10, 2015 8:05 am

Lets say the fabricator had put the faucet where you wanted (regardless of his own opinions). I assure you that one day you would look at that faucet centered over your 70/30 sink and regret that choice. It may even have garnered comments from anyone visiting your new kitchen. It would have stood out. You can't force symmetry were asymmetry is required.

countertopguy · Post by **countertopguy** » Sun Jun 05, 2016 12:15 pm

I couldn't agree more the hole is absolutely correct. It is just unfortunate that the communication between the customer wasn't better. Otherwise great job.

Jonathan · Post by **Jonathan** » Sun Jun 05, 2016 9:28 pm

countertopguy wrote:I couldn't agree more the hole is absolutely correct. It is just unfortunate that the communication between the customer wasn't better. Otherwise great job.

A year later

Dan R. · Post by **Dan R.** » Mon Jun 06, 2016 4:00 am

New member

Alex_Bores · Post by **Alex_Bores** » Mon Jun 06, 2016 10:39 am

x 100!

This is done correctly.

kevinp · Post by **kevinp** » Mon Jun 06, 2016 4:28 pm

Most fabricators typically try to adhere to industry standards. It is impossible to know what customers are thinking. The customer often doesn't know to ask a specific question thinking their general question covers the specifics. It's impossible to cover all the specifics during negotiations because so much is covered by industry standards and fabricators can't have all details covered in writing because the contract would be 50 pages long.

That faucet placement is dictated by the sink manufacture and is considered correct by me.

kevinp · Post by **kevinp** » Tue Jun 07, 2016 8:45 am

Crap! Didn't realize this post was a year old!

Darryl Miller · Post by **Darryl Miller** » Tue Jun 07, 2016 4:35 pm

kevinp wrote:Crap! Didn't realize this post was a year old!

I resisted the urge to point that out.......

RB Design · Post by **RB Design** » Wed Jun 08, 2016 2:36 pm

We are also a solid surface fabricator and there are residential sinks that are also solid surface and are 'fused' into the counter. Most of these sinks have a lower 'deck' behind the small sink intended for faucet, soap, and air gap. As mentioned before the whole intent of the offset is to offer a larger depth bowl on the right or left that would take up most of the deck, and not allow for a faucet.

The faucet is done correctly.

Stone Dude · Post by **Stone Dude** » Wed Jun 08, 2016 4:28 pm

STOP REPLYING TO THIS 1 YEAR OLD THREAD

ageless · Post by **ageless** » Wed Jun 08, 2016 5:11 pm

I agree....someone lock it! LOL!

Joe Durfee · Post by **Joe Durfee** » Thu Jun 09, 2016 9:08 am

ageless wrote:I agree....someone lock it! LOL!

done

Visit our Guardian Sponsors

Visit our Guardian Sponsors

Visit our Guardian Sponsors

Visit our Guardian Sponsors

Visit our Guardian Sponsors

Visit our Guardian Sponsors

Visit our Guardian Sponsors

Cry for HELP!! Kitchen faucet hole in wrong place??

Re: Cry for HELP!! Kitchen faucet hole in wrong place??

Re: Cry for HELP!! Kitchen faucet hole in wrong place??

Re: Cry for HELP!! Kitchen faucet hole in wrong place??

Re: Cry for HELP!! Kitchen faucet hole in wrong place??

Re: Cry for HELP!! Kitchen faucet hole in wrong place??

Re: Cry for HELP!! Kitchen faucet hole in wrong place??

Re: Cry for HELP!! Kitchen faucet hole in wrong place??

Re: Cry for HELP!! Kitchen faucet hole in wrong place??

Re: Cry for HELP!! Kitchen faucet hole in wrong place??

Re: Cry for HELP!! Kitchen faucet hole in wrong place??

Re: Cry for HELP!! Kitchen faucet hole in wrong place??